Solenoid Valve 39476825 36842318 39137492 92715614 Ingersoll Rand Compressor Spare Parts
Through some common solenoid valves not working,
1.The terminal of the solenoid valve of the screw air compressor is loose or the thread ends are dropped, and the solenoid valve is not powered, and the thread ends can be tightened to solve the problem.
2.The solenoid valve coil of the screw air compressor is burnt out. The solenoid valve coil is burnt out. You can remove the wiring of the solenoid valve and measure it with a multimeter. If it is open, the solenoid valve coil is burnt out. The reason is that the coil be affected with damp, resulting in poor insulation and magnetic flux leakage, resulting in excessive current in the coil and being burned down, so rainwater should be prevented from entering the solenoid valve. In addition, if the spring is too hard, the reaction force is too large, the number of turns of the coil is too small, and the suction force is not enough, the coil can also be burned. For emergency treatment, the manual button on the coil can be turned from "0" to "1" during normal operation to open the valve.
3.Screw air compressor solenoid valve stuck. The cooperation gap between the slide valve sleeve and the valve core of the solenoid valve is very small (less than 0.008m), and it is usually installed in a single piece. When mechanical impurities are brought in or there is too little lubricating oil, it is easy to get stuck.
Treatment method: Use a steel wire to poke through the small hole in the head to make it bounce back. The thorough solution is to remove the solenoid valve, take out the valve core and valve core sleeve, and clean it with CCI4 to make the valve core move sensitively in the valve sleeve. When disassembling, pay attention to the installation sequence of the components and the orientation of the external wiring, so that the reinstallation and wiring are correct, and check whether the oil spray hole of the lubricator is blocked and whether the lubricating oil is sufficient.
4.The solenoid valve of the screw compressor is leaking air. Air leakage will cause insufficient air pressure, making it difficult to open and close the valve. The reason is that the sealing gasket is damaged or the slide valve is worn, resulting in gas blowing in several cavities.
Pipeline filter element is mainly used to filter out solid particles and colloidal substances in the working medium, effectively control the degree of pollution of the working medium. Pipeline filter element flow path is expanded to reduce pressure drop, the shell is made of high quality aluminum alloy; Interior and exterior spray epoxy resin powder to improve durability and corrosion resistance; The inlet is connected with thread, and the air flow is marked on the shell, easy to install; O-seal leak-proof ring; Rib shell, easy to use elbow wrench; The pressure difference table suggests the best time to replace the filter element -- as far as possible to improve the filter investment utilization rate and reduce pressure drop (optional); The working pressure is 0.1~1.3Mpa, and the working temperature is less than 66ºC.
Pipeline filter can effectively remove these harmful impurities in the compressed air. As long as the compressed air filter is installed in the system and used with the cold drying machine or the drying machine, the compressed air can be provided to meet various quality requirements.
| Product Name |
Solenoid valve |
| Product Number |
39476825 |
| Use |
Ingersoll Rand Compressor |
| Brand |
QINGDAO FUTAI |
| Material |
Imported Material |
| MOQ |
1 PC |
| Delivery time |
5-7 days |
| Package |
Accordling Customer Request |
| Filtration efficiency |
99.99% |
| Specification |
Standard |
| Warranty |
12 months |
| Condition |
New |
| Dimension |
Standard |
Working principle of solenoid valve of air compressor
1: electricity, electromagnetic coil to produce electromagnetic force to shut down from the seat lift, valve | open; Power, the electromagnetic force disappears, the spring to close the pressure on the seat, the valve closed. 25mm2 principle: features: *3 principle: when energized, the electromagnetic force to open the pilot hole, The pressure of the upper chamber drops rapidly, forming a high pressure difference between the upper and lower parts around the closed parts, and the fluid pressure pushes the closed parts to move up, and the valve opens; When the power is off, the spring force to close the pilot hole, the inlet pressure through the bypass hole rapidly chamber in the closed valve parts around the formation of low high pressure difference, fluid pressure to push the closing parts to move down, close the valve.
2, direct acting diaphragm structure, step by step double structure, pilot membrane structure, direct acting piston structure, step by step direct acting piston structure, pilot piston structure.
Air compressor spare parts mainly cover brands such as Atlas copco, Ingersoll Rand, Sullair, CompAir, etc.
The main parts are air filters, oil filters, oil separators, preventive maintenance kit, solenoid valve, sensor, gear, couplings, coolers, etc.
We will meet the needs and interests of our customers, and provide high-quality parts and professional one-stop purchasing service.
Tips:
This is only a part of the part numbers, many oil separator filters P/N are not listed, in addition there are replacements filters for many other air compressor brands.
| Company Profile&Certifications: |
Now over 100,000 quality filters including compressed air filters, Hydraulic Filters and complete filter housing assemblies at wholesale discounts.
We offer OEM products as well as high quality replacements, engineered to precise OEM specifications and guaranteed to match the exact form, fit and function as the original equipment.
Our company is committed to continuous innovation and further improvement to create, improve the efficiency and productivity of excellence, to achieve the highest level of reliability and performance
1. Provide professional advice on the design of customers; Or according to the customer's request to provide solutions.
2. All filter element will be test before delivery, OEM and ODM order are accepted, Any kind of logo printing or design are available.
3. Good Quality + Factory Price + Quick Response + Reliable Service, is what we are trying best to offer you.
4. Professional online service; Professional before-sales and after-sales team to deal with your question on timely;
5.Supply sample list, reliable logistics guarantee, cooperation for many year,you only need to bear the freight;
6.If you have any question, please contact us freely by E-mail or Telephone.
Our company is located in the beautiful coastal city of Qingdao,is a professional manufacturer of air compressor filters and separators,
We repect the enterprise spirit of "steadyfastness,hard work and responsibility" and creat a good corporate environment based on the operation principle of "Integrity,reliability and innovation".
With the survival idea of "perfect technology, good service and excellent quality",
We always adhere to customer first,
aim at serving customer sincerely and touching customer with our service.
We plunge ourselves to provide clear and sustainable comprssed air to our customer,
meanwhile constantly pursue to save the sunning cost of compressor system for them.
Profession, concentration, focus is our corporate philosophy.
Q: Are you trading company or manufacturer ?
A: We are factory, you are very welcome to visit our factory at your convenience.
Q: What products do you supply?
A: FT Filter is a professional manufacturer of air compressor filters with rich experience. Mainly supplying: Replacement and customized filters of air compressors; Air compressor parts; Line Filters; Vacuum Pump Filters; Hydraulic Filters, for many air compressor brands: Atlas Copco, Bolaite, Gardner Denver, Fusheng, Liutech, Kaeser, CompAir, Quincy, Mann, Hitachi, Mitsuiseiki, Kobelco, Sullair, Ingersoll Rand etc.
Q: How long is your delivery time?
A: If there is stock, the lead time is about 2 working days after we get the payment. The specific delivery time depends on models and the quantity of your order.
Q: What's Minimum Order Quantity of your air compressor part?
A: the MOQ is 1pc, need you pay for the delivery cost.
Q: Can I become an Agent / DISTRIBUTOR of FT Filter?
A: Welcome! Please confirm the cooperation details and distributor qualification requirements with us, We have full advantages on quality and competitive price.
Q:What are the modes of transportation?
A:Sea, Air, International Express, Railway
Audited Supplier 
){kind=link}